![]() |
- Compact design: Motor, gear unit and electronics are combined in a single mechatronic drive system
- Simplified system planning and design
- A reduction in the number of variants allows for developing and designing standard materials handling systems with pre-fabricated and tested standard modules.
- The power of the drive engineering components is optimized to suit the application
- Reduction in storage due to reduced number of variants
- High degree of protection
- Hygienic surface design for applications in hygienic areas
- No air, dirt and germ swirls
- Low noise emission due to operation without fans (suitable for use in manual work stations)
- Reduced energy costs due to high efficiency of all components (gear unit, motor, electronics)
- High degree of reliability due to systematic development of all components
- Reduced total costs and operating costs of the materials handling system
- MGF.2 (torque class: 200 Nm)
- MGF.4 (torque class: 400 Nm)
- MGF.4/ET = “Expanded torque” option (expanded rated motor torque in continuous duty) (torque class: 400 Nm)
- MOVIGEAR® with hollow shaft and keyway
- MOVIGEAR® with TorqLOC® hollow shaft mounting system
The following figure shows a MOVIGEAR® MGFT.2 unit with TorqLOC® hollow shaft mounting system and a MOVIGEAR® MGFA.4 and MGFA.4/ET unit with hollow shaft and keyway:
![]() |
- Electronics cover without application slot
- Electronics cover with application slot
|
![]() |
- 1 digital output
- 4 digital inputs (two of them can be used as primary frequency input)
- 1 analog output
- 1 analog input
![]() |
- Wide voltage range 3 x AC 380 V to AC 500 V
- High overload capacity for all sizes
- 4Q capability due to integrated brake chopper and braking resistor installed as standard
- Line filter integrated as standard. EMC-compliant installation ensures compliance with limit class C3 to EN 61800-3 (class A, group 2 according to EN 55011).
- LED display for operating and fault states
- Protective features for complete protection of the frequency inverter and motor (short-circuit, overload, overvoltage/undervoltage, excess temperature in the frequency inverter, excess temperature in the drive unit).
- IPOS integrated positioning and sequence control
- Integrated STO safety function
- STO (safe torque off according to IEC 61800-5-2) by disconnecting the STO input.
- Performance level e according to EN ISO 13849-1.
- SS1(c) (safe stop 1, function variant c according to IEC 61800-5-2) by means of suitable external control (e.g. safety relay with delayed disconnection)
- Single control
- Reduction in the number of components
- Bus cables do not have to be routed in the field
- No risk of hidden faults in the bus cabling
- Reduced startup times
- Shorter project runtimes/reduction of project costs
- Optional motion control inputs (via plug connector) for local mode or sensor inputs
- As a drive for applications with high breakaway and starting torques.
- Conveyor systems with variable speeds
- As drive for applications that require soft and/or defined start-up behavior
- As group drive for easier implementation of synchronous operation
- Belt conveyors
- Pallet conveyors
- Roller and wheel conveyors
- Screw conveyors
- Container and packaging unit transports
- Chain and drag-chain conveyors
The following figures shows the principle of the MOVIGEAR® Single Line Network Installation:
![]() |
[1]
|
Safety switching device
|
[2]
|
Max. 10 x MOVIGEAR® in total
|
[3]
|
Permitted cable length between controller and last MOVIGEAR® max. 100 m
|
MOVIFIT® SNI has been designed for decentralized installation in the field. MOVIFIT®SNI allows to control up to 10 MOVIGEAR® drive units. The controller passes control information to MOVIFIT® SNI via Ethernet signals. MOVIFIT® SNI is the interface between the controller (PLC) and the connected MOVIGEAR® drive units.
![]() |
- Up to 10 MOVIGEAR® drive units can be connected
- Voltage range 3 x 380 – 500 V
- Integrated energy distribution
- Integrated communication interface
- Maintenance switch (not for the Hygienicplus design)
- 12 digital inputs + 4 digital inputs/outputs
- Aluminum die cast housing
- High rigidity
- IP65 version for industrial requirements
- Optional: Hygienicplus version for the food industry
- Separation of connection unit (ABOX) and electronics (EBOX):
- No damage to the electronics during installation and maintenance
- Fast replacement of electronics without wiring: Only one screw is required to connect the EBOX to the ABOX
For connecting a drive system with MOVIGEAR® SNI-B [4] to the fieldbus system PROFIBUS, DeviceNet, PROFINET or EtherNet/IP, you can operate MOVIFIT® SNI [3] together with the UFF41B/UFR41B fieldbus gateway [1]. Configuration and parameter setting is carried out using a plug-in in MOVITOOLS®MotionStudio.
![]() |
[1]
|
UFF41B/UFR41B fieldbus gateway with SD card OMG42B
|
[2]
|
Ethernet switch between UFF41B/UFR41B fieldbus gateway and MOVIFIT® SNI
|
[3]
|
MOVIFIT® SNI
|
[4]
|
MOVIGEAR® SNI-B
|